Real Homes is supported by its audience. When you purchase through links on our site, we may earn an affiliate commission. Here’s why you can trust us.

Wash away those bathroom DIY woes with this guide on installing a shower tray, whether its raised or low level

Get the best home decor ideas, DIY advice and project inspiration straight to your inbox!

Thank you for signing up to Realhomes. You will receive a verification email shortly.

There was a problem. Please refresh the page and try again.

Installing a shower tray is not as intimidating as it seems if you know-how. So save yourself from laborer costs, and learn a valuable skill at the same time with this bathroom tutorial.

Shower enclosures are not all equal. Aside from the shape of your base (be it quadrant, square, or rectangle), you'll also need to consider whether a height-adjustable or low-profile fitting is more suitable for your washroom setup. Luckily, whichever you decided to go for, we spoke to the bathroom pros who provided a step-by-step guide on both configurations. And, in case you didn't know, fitting a shower waste (aka shower trap) is another task you'll have to tackle, so as an added bonus, we've added some instructions on how to station this sanitaryware in your shower booth.

Then, you can go ahead and shop for your luxury fittings, like the best high-pressure shower head for that indulgent, spa-like experience.

'Height-adjustable shower trays use legs which are situated underneath the tray itself, raising the profile of it.' says Robert Tyson, bathroom expert, Victorian Plumbing (opens in new tab) . 'These are really popular as they allow you much easier access to the pipes if anything needs replacing in the future.'

1. An adjustable height shower tray 2. A good spirit level (opens in new tab) (or app on your smartphone) 3. Screws 4. An electric screwdriver (opens in new tab) 5. Shower waste tray (opens in new tab) 6. A watering can (opens in new tab) or kettle (opens in new tab) 7. Shower tray side panels 8. Silicone sealant (opens in new tab)

Firstly, place the shower tray loosely where you want to eventually install it to check for any fitment or clearance issues. 

Then, using a good drill and suitable screws (opens in new tab) , secure the legs into position and adjust the height to the level you require at this point (if you're lacking confidence with your tools, take a look at our guide on how to use a drill). Briefly fit the shower tray waste and check everything lines up correctly.

If you’re satisfied with the general fit of the shower tray waste component, you then need to establish the best possible route for your waste pipe if this isn’t already in place. Attach the waste to your tray then connect this to the trap.

If you're having trouble installing a shower tray waste, scoot down to the end where we've got a separate run-down of how to do this.

No one wants a wobbly shower tray so you'll need to use a spirit level to make sure that the tray is completely level. Check all angles just to be sure. This is an essential stage that shouldn’t be skipped over when placing this small bathroom shower idea. Because a sloped tray can cause quite a few problems further down the line (and needless to say, doesn't look nice either!)

You can either use a conventional spirit level or use an app on your phone. If you have an iPhone, simply search for the built-in Measure app (opens in new tab) or you can use something like Bubble level on Google Play (opens in new tab) .

With the shower tray level, it’s time to attach the underside of the waste to the waste outlet pipe. This obviously needs to be as secure as possible so make sure everything fits snugly and double-check if there are gaps or loose pipework anywhere.

Tyson's top tip: 'Use a watering can or kettle (full of cold water of course!) and pour some water into the waste. You’ll soon know if there’s something wrong.'

To tidy things up, attach your shower tray side panels to the tray to create a flush look. These should be really easy to attach, just pay attention to any instructions you get with the product as directions differ based on the hardware shape, size, and material type.

Take a good quality silicone sealant (like Gorilla Caulk & Seal, available on Amazon (opens in new tab) ) and carefully seal around the edges of the tray, creating a strong bond that will keep everything sturdy.

'Low-level shower trays are fitted directly onto the floor, which creates a neater and more streamlined look,' explains Liz Tabron, interiors blogger and author on Big Bathroom Shop (opens in new tab) blog.

If you're wondering how to fit a shower tray of this type, Tabron has the answers.

1. A pencil 2. A ruler (or measuring tape with millimeter increments) 3. Tape 4. A torch 5. A hole saw for shower tray waste 6. A jig saw 7. Waterproof sealant 8. Readymade mortar mix or cement and sand 9. A plastering trowel 10. Glass suction lifters to get the tray in place.

Ensure you know where the underfloor joists are. To find them, you'll need to lift your bathroom floorboards. Once you can see them, draw a pencil line to identify where the under-floor joist is positioned. This will help you to position the shower tray correctly.

Ensure the area you've chosen to place your shower tray is level, you can now position it at a 90-degree angle flush to the walls. Next, take your pencil and draw around the outer edges.

Again, with your pencil, outline the shower tray’s waste hole onto the floor below and also draw a line 8mm from the floor, along both walls. This will help you to identify the depth of your mortar placement.

Use your torch to make sure there isn’t any electrical wiring beneath the floor prior to drilling or cutting.

Having made your outlines you may now remove the shower tray and, using your hole saw (opens in new tab) , cut out the space you will need for the shower tray waste. Having cut out the relevant space, check that the waste trap fits easily into the hole you have created. If the fit is a little too snug, use your jig saw (opens in new tab) to make the hole bigger.

Note: Ensure the shower tray waste trap is positioned correctly to take into account underfloor plumbing.

Before mixing your mortar, you should apply a waterproof sealant (like Henkel's clear silicone sealant on Amazon (opens in new tab) ) to the entire area upon which the shower tray will sit.

When preparing mortar, you should use a 5:1 mix, meaning one part cement to five parts sand. You should also aim to create a thick, or stiff mix, which you will then apply as a base for your shower tray, prior to the shower tray installation.

Once you've prepared your mortar you can begin applying it in the chosen area. Remember to level off your mortar at the 8mm line, which you measured earlier.

Once your bed of mortar is level (use your plastering trowel (opens in new tab) ), it is time to place your shower tray into the correct position. Your shower tray will come with a plastic covering. Before bedding your tray into place, be sure to peel back the plastic along each wall-facing edge. It can be secured with tape along the top edge.

Now that your mortar is laid, it becomes difficult to lift and place the shower tray in position with the required degree of accuracy. This is when your glass suction lifters (opens in new tab) are essential. However, don’t forget to give your shower base a “test lift” prior to allowing the lifters to take the full weight. Place the shower tray in position and use your level to ensure its level. Using a small trowel, remove excess mortar from around the base, and allow 24 hours for the mortar to set. Once set apply a good quality silicone sealant around the edges where the shower tray meets the wall. This should be applied liberally in order to fill any gaps.

'A shower waste (often also referred to as a "shower trap") connects to the underside of the shower tray beneath the floor of the shower and works to support the water flow,' explains Adam Chard, bathroom expert, Victoria Plum (opens in new tab) . 'It is connected to the shower trap piping, which is similar to the trap found under the kitchen sink, where waste water from the taps above can drain out into external sewage systems.'

'If water is not able to drain effectively, it can create a pool of dirty water as you wash, while also potentially leading to leaks and other forms of damage in and around the shower area.' Method:

Remove the masking from around the shower tray waste area by carefully peeling it away. Make sure to keep the masking on the rest of the tray to keep it protected.

Apply a small bead of silicone sealant to the waste top nut flange, which ensures a waterproof seal.

Inset the waste into the shower tray and hold the trap underneath.

Once you’re happy the waste is in the correct position, tighten it in a clockwise direction until it’s as tight as you can get it. Then, wipe away any excess sealant and position the top part with the chrome cap into the waste hole.

No, grout isn't the right material to finish your shower tray with because of its fragility, as one expert explains:

'Make sure you have silicone sealant and not normal grout,' says Alex Hyslop – senior marketing manager, product Mira Showers (opens in new tab) .

Grout isn’t suitable for sealing around your bathtub or shower tray as it’s not flexible and will crack as soon as any weight is placed on the tub or tray. 

'Different suppliers provide instructions on how to install their own brand of shower tray depending on the material of the tray however the most common and effective way to install a shower tray is on a bed of concrete to ensure the tray is completely supported under its base,' says Lydia Luxford, technical manager at Easy Bathrooms (opens in new tab) .

'Only trays supplied with leg raiser kits are suitable for fitting raised from the floor. It is important to be aware, that shower trays should not be installed directly on a timber floor as timber moved through expansion and contraction which would cause the tray to move or crack.'

'Thermal and concrete boards are available in different sizes and can be used underneath the base of the tray before applying concrete to prevent future movement issues alternatively Marine ply with a minimum thickness of 12mm or standard ply with a minimum of 18mm thickness (must be primed) can be used.'

'Always follow the instructions provided by the supplier,' advises Luxford.

'If the floor is concrete, clean the area, use a primer to prepare the surface of the concrete then you can lay the concrete to install the tray, it is important to wiggle and tap the tray gently when installing onto concrete to remove any air gaps caught in the mix.'

'If the floor is timber, install either concrete, thermal, or 12mm Marine ply boards over the timbers, then follow the same instructions as above. You must check the tray for level around all of the edges before allowing the concrete to set.'

'Yes, always place your tray in position before installing any tiles or shower boards.' says Luxford.

'It is good practice to also install a strong bead of anti-mold silicone around the edge of the tray during installation to prevent any water leakage under the tray should water ever get down the back of the tiles/boards.'

Christina joined the Real Homes team as a digital writer in June 2021. Prior to this, she worked for Good Homes magazine and home interest events including the Ideal Home Show and Grand Designs Live. She lives close to Epping Forest and is spoiled for choice with lush green spaces, but loves her own English garden that adjoins her ground-floor maisonette, complete with a floral melange of roses, lavender, jasmine, and an apple tree.

The Xiaomi Mi Smart Air Fryer is not only app-compatible, but also has a sleek and high-tech design that's very enjoyable to use. But how good is it at air frying?

By Millie Fender • Published 9 July 22

Whatever your budget, you can find something to love for your home during the Nordstrom Anniversary Sale and get your home looking luxe for less

By Jaclyn Turner • Published 9 July 22

Real Homes is part of Future plc, an international media group and leading digital publisher. Visit our corporate site. © Future Publishing Limited Quay House, The Ambury, Bath BA1 1UA. All rights reserved. England and Wales company registration number 2008885.